DW-GP NDIR Infrared Methane (CH4) Sensor Module, UART and Analog Output

DW-GP

NDIR Infrared Methane (CH4) Sensor Module, UART and Analog Output

Non-dispersive infrared (NDIR) methane sensor module, Ø20 mm, with selectable 0–5% vol, 0–10% vol or 0–100% LEL range, UART and 0.4–2.0 V analog output and built-in temperature compensation, for industrial safety, HVAC and agricultural monitoring.

Measuring range
0–5% vol, 0–10% vol or 0–100% LEL
Output
UART + 0.4–2.0 V
Measuring principle
NDIR

Features

  • NDIR measurement: independent of oxygen, good selectivity
  • UART and analog voltage outputs
  • Built-in temperature compensation, linear output
  • Resistant to poisoning and to water vapour interference
  • Can directly replace catalytic gas sensors
  • Long service life of more than 5 years

Typical applications

  • HVAC and refrigeration
  • Indoor air monitoring
  • Industrial process control and safety
  • Agriculture and animal husbandry
  • Sites with flammable or explosive gases

Full specifications

PDF DW-GP Datasheet EN
DW-GP specifications as published. Values are typical unless stated.
Performance
Measuring mediumMethane (CH4)
Measuring principleNon-dispersive infrared (NDIR)
Measuring range0–5.00% vol / 0–10.00% vol / 0–100% LEL (selectable)
Resolution0.01% vol; 1% LEL
Response timeT90 < 30 s
Warm-up time3 min
Temperature compensationBuilt-in temperature sensor
Output
Output signalUART (3.0 V level) / analog voltage 0.4–2.0 V DC
Analog output scaling0.4–2.0 V = zero to full range; 0 V on self-test fault
Baud rate9600 (8 data bits, 1 stop bit, no parity)
Electrical
Supply voltage3.6–5.0 V DC
Average current< 85 mA
Pin definition1 GND, 2 Vin, 3 UART RXD, 4 Vout (0.4–2 V), 5 UART TXD
Mechanical
DimensionsØ20 × 22.6 mm
Weight35 g
Ingress protectionIP54
Environmental
Operating temperature−20 to +60 °C
Operating humidity0–95% RH, non-condensing
Service life> 5 years

Questions about the DW-GP

What is the measuring range of the DW-GP?

The DW-GP (NDIR Infrared Methane Sensor Module) has a measuring range of 0–5.00% vol / 0–10.00% vol / 0–100% LEL (selectable).

What output signal or interface does the DW-GP use?

The output of the DW-GP (NDIR Infrared Methane Sensor Module) is UART + 0.4–2.0 V.

What is the IP rating of the DW-GP?

The DW-GP (NDIR Infrared Methane Sensor Module) has an ingress protection rating of IP54.

What supply voltage does the DW-GP need?

The DW-GP (NDIR Infrared Methane Sensor Module) is powered by 3.6–5.0 V DC.

What is the DW-GP used for?

The DW-GP (NDIR Infrared Methane Sensor Module) is typically used for HVAC and refrigeration, indoor air monitoring, industrial process control and safety, agriculture and animal husbandry, and sites with flammable or explosive gases.

Where can I get the DW-GP datasheet?

The DW-GP datasheet is a free PDF on this page, with the full specification table. For drawings in CAD format or a custom version, contact DWIN sales.

Does DWIN offer OEM or custom versions of the DW-GP?

Yes. DWIN adapts the DW-GP from its existing design: housing and mounting, cable and connector, interface and protocol, firmware and range. Engineering confirms feasibility, then DWIN builds samples for your tests before series production.

How do I get a quote or samples of the DW-GP?

Use the quote form on this page or email xyx@gzdwin.com with the DW-GP, your quantity, application and destination country. DWIN sales replies with pricing, lead time and sample availability.

Ask about the DW-GP

Send your application, quantity and interface. We reply with pricing, lead time and sample availability.

Request a quote