DW-GD Fixed Gas Detector, 4–20mA or RS485, Three Relays

DW-GD

Fixed Gas Detector, 4–20mA or RS485, Three Relays

Fixed gas detector for combustible and toxic gases with LCD display, 4–20 mA or RS485 bus output and three relay outputs, set up by infrared remote control, in an aluminium or stainless steel housing with IP67, for refineries, chemical plants and power stations.

Output
4–20 mA or RS485
Relay output
3 relays
Protection
IP67

Features

  • Combustible or toxic gas, natural diffusion sampling
  • 4–20 mA analog or RS485 bus digital output
  • Three relay outputs: two volt-free contacts and one active relay
  • LCD display
  • Non-contact setup by infrared remote control
  • Smart sensor module, free of calibration, easy to maintain
  • Explosion-proof version available on request

Typical applications

  • Petroleum and petrochemical industries
  • Refineries
  • Chemical plants
  • Metallurgy
  • Power industry
  • Other sites where harmful gases may occur

Full specifications

PDF DW-GD Datasheet EN
DW-GD specifications as published. Values are typical unless stated.
Performance
Measured variableCombustible gas, toxic gas
Sampling methodNatural diffusion
Response timeCombustible (LEL): T90 ≤15 s; toxic: T90 ≤30 s
Output
Output signal4–20 mA, or RS485 bus (digital)
Relay output3 relays: 2 volt-free contacts, 1 active relay
Electrical
Power supply24 V DC ±6 V
Power consumption≤2.5 W
Interface
DisplayLCD
ConfigurationInfrared remote control
Status indicationYellow: fault; red: alarm; green: power
Environmental
Operating temperatureCombustible: −40 to +70 °C; toxic: −20 to +50 °C
Operating humidity≤95% RH, non-condensing
Atmospheric pressure86–106 kPa
Ingress protectionIP67
Hazardous-area versionExplosion-proof version available on request
Mechanical
Housing materialAluminium alloy (stainless steel optional)
Cable entryNPT 3/4 (adapters for other sizes)
Dimensions130 × 154 × 95 mm
WeightApprox. 1.2 kg (aluminium); 4.2 kg (stainless steel)

Questions about the DW-GD

What output signal or interface does the DW-GD use?

The output of the DW-GD (Fixed Gas Detector) is 4–20 mA or RS485.

What is the IP rating of the DW-GD?

The DW-GD (Fixed Gas Detector) has an ingress protection rating of IP67.

What supply voltage does the DW-GD need?

The DW-GD (Fixed Gas Detector) is powered by 24 V DC ±6 V.

What is the relay output of the DW-GD?

The DW-GD (Fixed Gas Detector) is specified with a relay output of 3 relays.

What is the DW-GD used for?

The DW-GD (Fixed Gas Detector) is typically used for petroleum and petrochemical industries, refineries, chemical plants, metallurgy, and power industry.

Where can I get the DW-GD datasheet?

The DW-GD datasheet is a free PDF on this page, with the full specification table. For drawings in CAD format or a custom version, contact DWIN sales.

Does DWIN offer OEM or custom versions of the DW-GD?

Yes. DWIN adapts the DW-GD from its existing design: housing and mounting, cable and connector, interface and protocol, firmware and range. Engineering confirms feasibility, then DWIN builds samples for your tests before series production.

How do I get a quote or samples of the DW-GD?

Use the quote form on this page or email xyx@gzdwin.com with the DW-GD, your quantity, application and destination country. DWIN sales replies with pricing, lead time and sample availability.

Ask about the DW-GD

Send your application, quantity and interface. We reply with pricing, lead time and sample availability.

Request a quote